The cable spiker is a special equipment, mainly used for further destructive identification of cables after cable identification and before sawing.
In the process of power cable construction, when migrating and repairing the laid cables, it is often necessary to saw off the relevant cables. In order to ensure the operator's personal safety foolproof. First of all, it is necessary to judge whether the relevant cables on site are live or not. Only after confirmation can the relevant cables be sawed off.
The method of absolutely confirming whether the cable is live is currently only the method of short-circuiting the cable relative to the ground or relative to the phase by mechanical puncture.
The cable stabbing device adopts a remote control/automatic piercing device, which can damage and pierce the relevant cables once on site. If the cable is electrified, the cable will explode when punctured, otherwise the cable will not be electrified.
Product Parameters
Cable Spiker
Recognition method: Judging by the swing direction ofthe hands
Jaw:中125mm
Power: 1.5kVA(intermittent momentary)
Weight: 11.00kg
Dimensions:430X360X225mm
Signal sending frequency: Min: 0.4Hz, Max: 1Hz (range adjustable)
Features:
1. When the angle between the two guns is not 120°, at least one gun body can achieve the purpose of stabbing and form a short circuit point;
2. Use wired + wireless remote control method to control, and can be remotely controlled through the wall;
3. Both AC and DC, built-in lithium battery pack and large-capacity energy storage device, long charging time;
5. Small size and light weight, very suitable for outdoor use. Technical Parameters
| Shooting device | 2 gun bodies; |
| Remote control distance | greater than 10 meters, can be remote controlled across the wall; |
| Control line length | 5 meters; |
| Clamp diameter | φ30-150mm; |
| Working power supply | charging AC 220V/50Hz, built-in battery can work continuously for more than 10 hours; |
| Controller | 270×230×120mm 2.5kg; |
| Complete set | 470×380×210mm 15.5kg (double gun 506Y). |
Nail specification table:Nail specification table
| Cable diameter mm | 30 | 40 | 50 | 60 | 70 | 80 | 90 | 100 |
| Nail specifications | PS27C8 | PS37C8 | PS47C8 | PS52C8 |
Bullet power table:
| Specification | black | blue | yellow | red | Recommended Use | 35kV and below | 35kV and above |
| Power | smallest | small | middle | big | Use S1 yellow | Use S1 red (6.8*11mm) |
Standard configuration: 50 rounds of S1 red (power level 5) bullets, 50 rounds of PS57C8 nails
Operation interface introduction
1. Grounding: grounding point of the instrument, safety protection;
2. Output 1: used to connect to the shooter body;
3. Output 2: used to connect to the shooter body;
4. Charging: DC12V charging port, connect to a 12V charger to start charging;
5. Switch: turn on/off the working power;
6. Indicator light 1: when output 1 is working, the indicator light is on;
7. Indicator light 2: when output 2 is working, the indicator light is on;
8. Power indicator: when the built-in battery is working, it indicates the battery power in real time.
1. Controller: control the shooter to carry out the cable puncture action process;
2. Remote control: The two buttons (A.B) of the remote control correspond to output 1 and output 2 of the controller;
3. Bullet: Loaded into the chamber when stabbing;
4. Shooting nails: put them into the nail tube when stabbing;
5. Shooter
6. Output line: the connection line between the controller and the shooter;
7. Ground wire: the connection wire between the shooter and the ground drill;
8. Ground drill: Generally, there is no formal grounding point on site, so find a reliable ground to insert;
9. Screwdriver, socket, test tube brush: accessories for cleaning the shooter;
10. Power cord (charger): Control box charging cable.
Product Tags:
|
|
Underground Cable Fault Locator with Remote Control Spiking Tool Images
|
